M-270+ AC/DC Digital Clamp Tester

Multi

No reviews yet Write a Review
SKU:
multi-M-270+
AED0.00
AED0.00

Description

MULTI M-270+ AC/DC Digital Clamp Tester

Product Overview

The MULTI M-270+ AC/DC Digital Clamp Tester is a versatile measuring instrument designed for AC and DC current measurement up to 2000 A. Equipped with a large 55 mm diameter clamp jaw, it allows current measurement without disconnecting the conductor.

The instrument features True RMS measurement for AC current and AC voltage, providing accurate measurement of non-sinusoidal waveforms within its specified operating ranges. In addition to current measurement, the M-270+ supports AC/DC voltage, resistance, frequency, diode and continuity testing.

With a 4000-count LCD display, manual and automatic range selection, DC current zero adjustment, data hold and automatic power-off functions, the M-270+ is suitable for a wide range of electrical inspection, troubleshooting and maintenance tasks.

Key Features

  • AC and DC current measurement up to 2000 A

  • 55 mm diameter clamp jaw for larger conductors

  • True RMS measurement for AC current and AC voltage

  • AC/DC voltage measurement up to 600 V

  • Resistance measurement up to 40 MΩ

  • Frequency measurement up to 1000 kHz

  • Diode test and continuity check

  • 4000-count LCD display

  • DC current automatic zero adjustment

  • Data hold function

  • Automatic and manual range selection, depending on measurement function

  • Automatic power-off after approximately 10 minutes

  • Low battery indication

Measurement Functions

AC/DC Current Measurement

The M-270+ measures both alternating and direct current through its clamp sensor. The maximum AC/DC current input is 2000 A, with the manufacturer's specified time limitation of up to 3 seconds at this maximum input.

AC/DC Voltage Measurement

The instrument provides AC and DC voltage measurement with ranges up to 600 V. True RMS measurement is available for AC voltage.

Resistance Measurement

Resistance can be measured over multiple ranges up to 40 MΩ, supporting electrical testing and troubleshooting tasks.

Frequency Measurement

The frequency measurement function covers ranges from 100 Hz up to 1000 kHz, with automatic range selection.

Additional Functions

  • Diode testing

  • Continuity checking with audible buzzer

  • Data hold

  • DC current zero adjustment

  • Low battery indication

  • Automatic power-off

Applications

The M-270+ can be used for electrical measurement and troubleshooting activities such as:

  • AC and DC current measurement

  • Electrical equipment inspection

  • Electrical maintenance and troubleshooting

  • Voltage and resistance checks

  • Continuity and diode testing

  • Measurement of conductors that fit within the 55 mm clamp opening

Safety and Operating Instructions

The M-270+ is specified by the manufacturer as meeting IEC 61010-1 and IEC 61010-2-032, Installation Category III 600 V phase-to-earth.

Important safety warning: The manufacturer's instruction manual explicitly warns against measuring power lines carrying more than 250 V and states that the instrument should not be used to measure power lines because transient voltage spikes may occur. The manual also prohibits measurements on uninsulated conductors or busbars.

Always read the instruction manual and observe the specified input limits and safety precautions before use.

Extra Information

Brand:
Multi
Brand:
MULTI
Product Type:
AC/DC Digital Clamp Tester
AC Current Range:
40 A / 400 A / 2000 A
AC Current Accuracy:
±2.0% rdg ±8 dgt (40 A) ; ±1.5% rdg ±8 dgt (400 A / 2000 A)
DC Current Range:
40 A / 400 A / 2000 A
DC Current Accuracy:
±2.0% rdg ±8 dgt (40 A); ±1.5% rdg ±8 dgt (400 A / 2000 A)
AC Voltage Range:
400 mV / 4 V / 40 V / 400 V / 600 V
DC Voltage Range:
400 mV / 4 V / 40 V / 400 V / 600 V
Voltage Accuracy:
±1.2% rdg ±8 dgt
Resistance Range:
400 Ω to 40 MΩ
Frequency Range:
100 Hz to 1000 kHz ( ±0.5% rdg ±3 dgt )
Continuity Test:
Audible buzzer, approximately below 40 Ω
Diode Test:
Available
Display:
3.5-digit LCD, maximum reading 3999
Measurement Method:
Dual slope integration
AC Measurement:
True RMS
Clamp Jaw Opening:
55 mm
Sampling Rate:
3 times/sec
Data Hold:
Yes
DC Zero Adjustment:
Yes
Auto Power Off:
Approximately 10 minutes
Safety Standards:
IEC 61010-1; IEC 61010-2-032
Installation Category:
CAT III 600 V phase-to-earth
EMC Standard:
EN 61326
Operating Temperature:
0°C to +40°C
Storage Temperature:
−10°C to +60°C
Power Supply:
AAA 1.5 V batteries
Power Consumption:
36 mW
Battery Life:
Approximately 60 hours continuous
Dimensions:
85 × 240 × 34 mm